pilot1 · proof of concept

One plate, three kinds of subject.

Pale line work on dark metal, engraved the same way whatever it is about: the flying an aeroplane actually did, the figures out of a granted patent, or a shop drawing off an engineer's desk. Pick a subject.

Five real aircraft, and one real trip.

A live lookup reaches back about 25 hours. These came out of the daily archives instead, several days each, so you can see what a week of an aeroplane's actual flying prints like. The last one is not an aircraft at all: it is somebody's return trip, and the way out and the way home were different aeroplanes. Pick one, or type any US tail number and it looks that aircraft up live. Change anything and it redraws.

Loading 31,000 airports…

N628TS
What is real here and what is not. The aircraft is real: type, registered owner, the ICAO24 hex it actually transmits and a photograph of that airframe, looked up live from adsbdb. The routes are the tracks the aeroplanes actually flew, not arcs between two airports — every ADS-B point carries position, barometric altitude, ground speed and heading about every twenty seconds, and the figures on the plate are read off those points. That is why the distance runs a few percent over the direct line, and why one leg in this sample runs 36% over: it went around weather. Airport coordinates are real too, from OurAirports. Flights come by one of two routes. Live, the track comes from adsb.lol and is cut into flights at its takeoffs and landings — but that network keeps only about 25 hours, so a parked aeroplane returns nothing and you can type the airports yourself instead, which draws a great circle because two codes is all that is known. The four aircraft above came from adsb.lol's daily archives, which are free and do go back years; three days were pulled and stitched together through the same code the live lookup uses. That is the finding that matters: history is obtainable, just not from an endpoint you can ask a question of — it arrives as a 4 GB tarball per day, which is a job to run after an order, not while somebody waits.

Asked: can we spot a first solo and market to them?

Not from flight data. Not even close.

ADS-B identifies the airframe, never the person, and carries no occupancy field at all. A first solo and the two hundred dual lessons before it are the same shape in the data: a trainer flying circuits at its home field. The aeroplane belongs to the school rather than the student, so the registration says nothing about who was in it either.

Where a first solo genuinely is visible is the flight school's own Facebook and Instagram, because of the cut-shirt tradition. That is monitoring named individuals on social platforms, which is a different business with a different set of problems.

The public-record route that does work is one step later. The FAA Airmen Certification Database is free, updated monthly, and carries one row per certificated airman with a mailing address. It does not flag new certificates — but diffing two consecutive months gives you exactly the people certificated in between.

  • That is the checkride, not the solo. Months later, and arguably the better moment anyway: a certificate is a thing you frame, and a first solo is a haircut.
  • Airmen can opt out of address release, and those records are excluded. You are marketing to the ones who did not opt out.
  • Monthly latency, and no certificate numbers in the file.

Making one for real

What it costs to produce these yourself.

The design is pale lines on a dark ground, which is the opposite of how most engraving works. Cutting into metal normally makes a dark mark. What produces this look is marking a dark coating so the bright metal underneath shows through, which is why anodised aluminium appears in most of the options below.

ApproachMachineSoftwarePer plateTurnaround
Diode laser on anodised aluminium $200–900$60–120 $6–18 blankMinutes
IR / fiber marker on anodised or bare metal $1,300–4,000Included $6–18 blankUnder a minute
CNC with a diamond drag bit $200–2,500$0–350 $6–18 blank20–40 min
Printed circuit board — one-off —Free $65–2201 week + freight
Local trophy or award shop —— $30–60Days

Diode laser

The cheapest way in. A 10–20 W blue diode ablates the dye in anodised aluminium without touching the metal beneath. Entry gantry machines start around $200; the Atomstack Atelier is a 12 W galvo at $899, and the wider Atomstack range covers the cheap end. Also cuts wood, acrylic and leather.

Bright silver-white lines on matte black. Closest thing to the screen, and the lines stay hairline-fine.

IR or fiber marker

The right tool rather than the cheap one. The xTool F2 pairs a 5 W IR head with a diode and starts at $1,299. Standalone 20–30 W markers from SFX or OMTech sit around $1,500–4,000. Branded MOPA units reach $12,000 and are built for colour on stainless, not this.

Same as the diode but faster and finer, and it marks bare steel and brass too — though on bare metal the mark goes dark on bright, which inverts this design.

CNC with a diamond drag bit

A spring-loaded diamond scratches a bright groove through the anodising. No laser safety, no fumes. A Genmitsu 3018-class router starts near $200; a rigid desktop mill runs to $2,500. Slow: a dense flight track is twenty to forty minutes.

The only option with real depth. The groove catches the light as you tilt it, and you can feel the track with a fingertip.

Printed circuit board

Dark soldermask with white silkscreen, optionally with gold ENIG accents. The only option needing no machine at all, and the cheapest by far if the same design is made repeatedly. Price it on the JLCPCB quote tool or at PCBWay.

Matte, flat and printed rather than marked. It looks like electronics, which is either the charm or the objection.

The minimum order is about five boards, and every customer's plate is a different design, so there is nothing to amortise it across. A bespoke one-off costs the whole order.

Board cost, at the sizes these plates want

Board houses will not make one. The minimum is around five, so the cost of a single bespoke plate is the cost of the whole order — the four spares are scrap, because the next customer's flights are a different board.

SizeMinimum orderExpress freight One bespoke plateEach, if a design repeats
5 × 7 in 127 × 178 mm $40–70$25–45 $65–115$13–23
8 × 10 in 203 × 254 mm $90–160$30–60 $120–220$24–44

Fabrication is about a week. The long pole is freight, not production: economy air is the multi-week figure, while DHL or FedEx express is typically 3–6 days. Five 8 × 10 boards in 1.6 mm FR4 weigh roughly 800 g, which is what puts express in the $30–60 band rather than the $80 one.

That reverses the obvious conclusion. A circuit board is the cheapest way to make fifty of one design and the most expensive way to make one of fifty designs, which is exactly what a plate of somebody's own flights is. The machine routes cost more up front and then never charge more than a blank, whatever is on it — an anodised blank is $6–18 whether it is the first plate or the four hundredth.

Machine prices were read from the linked pages on 19 September 2026 and will drift.
Board and freight figures are estimates, not quotes — both scale with area, layer count and finish, so run the real quote before committing.
Every route needs the artwork as a vector at physical size: LightBurn ($60–120) drives the lasers and reads SVG directly; CNC and PCB want DXF and Gerber respectively.